Anker Soundcore Life Q30 Button Replacement

Written By: Nathan
  • Comments: 2
Anker Soundcore Life Q30 Button Replacement

Difficulty

Difficult

Steps

9

Time Required

45 minutes

Introduction

This guide will show you how to replace the buttons on the Anker Soundcore Life Q30 headphones. There is a volume down button, a volume up button, and a mute button on the right side, and the power button and noise cancelling button on the left side. This guide will cover a general process for opening up the device and replacing the buttons, starting with the left side. Replacing these buttons will require you to solder their replacements onto the circuit board. Before you begin, make sure to turn off the headphones and unplug them from their charger.

  1. MFbPvrPJWnAafMKl
    MFbPvrPJWnAafMKl
    3fWaoYPfNiHr2bNv

    • Orient the headphones such that the headphone speakers are closest to you, and the headband is furthest from you.

    • Adjust the folding hinge to where the speakers are facing up.

    • Make sure you can easily reach the edge where the cushion connects to the rest of the headphones.

  2. Ch2fJ44SjHwaXasZ
    Ch2fJ44SjHwaXasZ
    56vVcntGuIU44hEq
    ViMNYRmXZTNi141i

    • Using one hand, hold the right side of the headphones still.

    • Using your other hand, slide the plastic opening tool in the edge along the cushion.

    • Gently pry the cushion off using the plastic opening tool.

    • Set the right ear cushion aside and repeat this step for the left side of the headphones.

  3. 1m6gCfhXHdenG3NX
    1m6gCfhXHdenG3NX
    YKopSMaC1EZ1tCKi
    pFcSbLXXMMYoJ6YT

    • Remove the four 5.7 mm screws from the headphone driver using a Phillips #00 screwdriver.

    • Pull the headphone driver apart from the headphones.

    • If you’re having difficulty doing so without any tools, use tweezers to get a better grip on it.

  4. NooXcLpcJlNTZOfI
    NooXcLpcJlNTZOfI
    3jXlLZifPOfpyfyU

    • Lift the drivers out of the headphones.

    • Remove the wires from the circuit board that connect the drivers.

    • Take note of where the wires are connected, as you will have to solder them back to the circuit board.

  5. i5yJ4grduaA5tFJR
    i5yJ4grduaA5tFJR
    IAObdKVFXnxPseMF
    L4awiS6GaPhMovRU

    • Pull the microphone (circular blue part) from its socket by the connected red wire that is covered in black rubber.

    • Take note of where the microphone is, as you will have to reconnect it.

    • The wire itself is connected to the battery and will disconnect the battery from the exterior piece of the earcup.

    • Unscrew the four 5.7 mm screws with a Phillips #00 screwdriver connecting the earcup to the headphone’s frame.

    • Remove the earcup.

    Unscrew the four 5.7 mm screws with a Phillips #00 screwdriver connecting the earcup to the headphone’s frame.

    Six 5.7 mm screws

    Igor Yakovlev -

  6. IQJuLkQWPAq2C2Na
    IQJuLkQWPAq2C2Na
    SNFYSDVPlNkeNLMe

    • Unscrew the 5.7mm screw with a Phillips #00 screwdriver within the green circuit board connected to the battery.

    • Carefully pry the green circuit board and battery off of the earcup.

    • The battery may be glued into place, which will require some force to remove.

  7. mFi1J4ndBkDZLKij
    mFi1J4ndBkDZLKij
    H5FMjWmLSNy1qesU

    • If you are following this guide to reach the buttons, ignore this step.

    • Remove the wires connecting the battery from the circuit board.

    • Note the placement of the wires you remove, as you will have to solder them back into place.

    I can't believe you left out the most important part. What are the dimensions and mAh capacity of the Battery. Where can we order one? I certainly don't want to begin this job without having a replacement battery, ready to be installed.

    Ron Cerrato -

  8. vTwZkMtMxvjjsxZW
    vTwZkMtMxvjjsxZW
    1QJNhjTG4ZEbUgsc
    MdKJSqBwJKhWfvEZ

    • You can follow a similar process to open up the right side of the headphones. The main difference is that there is no battery to remove, so there will just be a circuit board that will need to be removed from the earcup.

  9. hCvitwUqRLZp5Vpm
    hCvitwUqRLZp5Vpm
    sIvKSBYnGakLbCHm

    • After the circuit boards can be accessed, you will need to desolder the button you are trying to replace from it. This guide will be using the right side of the headphones as an example, but the process will be the same for the buttons on the left side. This link will take you to a guide on soldering.

    • You can now solder your replacement button into place. Take care that you orient the button correctly so that it matches the position of the external part of the button.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Nathan

Member since: 15/02/24

450 Reputation

0 comments