Dispenser Disconnection (Prereq)

Written By: Bill Gilbert
  • Comments: 1
Dispenser Disconnection (Prereq)

Difficulty

Moderate

Steps

14

Time Required

No estimate

Introduction

  1. IWjgsUtZOIuShVqa
    IWjgsUtZOIuShVqa
    cmisDLhhQ1ZspJJT

    • Before you begin your repair, perform the following:

    • Turn off the main water supply

    • Unplug your washer

    • Disconnect all water connections at the rear of your washer

    DO NOT USE THESE Instructions 🤦‍♂️. It will take you for ever. Go from the back, lie down on the ground take it I’ll put the new one in done. Or do it with someone you leave it a tad side ways and even easier

    Mechanicbob -

  2. a1CEVEuZVuhsJs3v
    a1CEVEuZVuhsJs3v
    s1Dx6pURHR66tbUG
    WMesicEUoODuO1DI

    • Use a Phillips driver to remove the two bottom 16.5 mm-long screws securing the top panel brackets.

  3. MXS5aiRAHxRbjTgD
    MXS5aiRAHxRbjTgD
    BqIF6FiMQVaOIZZQ

    • Slide the top panel 1-2 inches towards the rear of the device to disconnect its clips.

  4. vk2XTwmpQAn5SSnW
    vk2XTwmpQAn5SSnW
    mKqTwIkkot2M6aDA

    • Tilt the top panel upward to completely disconnect it from the chassis.

    • Remove the top panel.

  5. 4sgimkxaXD3ejSwK
    4sgimkxaXD3ejSwK
    bkCBDPSK6YgGYTcr

    • Pull the detergent drawer away from the chassis as far as it will go.

  6. P6jShSDIRVTufbKa
    P6jShSDIRVTufbKa
    XRPBgqFyjRWpSKkn
    oCBTknIPcxBXF3VM

    • Press down on the "Push" button to disengage the clips securing the detergent drawer.

    • Pull the drawer out of its slot on the chassis and remove it.

  7. Sh1lUfSYKsCUbib6
    Sh1lUfSYKsCUbib6
    FHuG6LDAjUcGYWvr
    io46keEPByRWavUB

    • Disconnect the three harness connectors for the control panel.

    • Always grip cables by their connectors and not the wires themselves.

  8. P2pQDgkIGMBLIEsQ
    P2pQDgkIGMBLIEsQ
    qAENSdyEVOowrsq5

    • Use your hands to unclip the control panel cable from the detergent dispenser.

  9. qTuTCBjdVucECxXZ
    qTuTCBjdVucECxXZ
    fTAtxveCC1FKMitV
    Ky2ypHXUQVPGLCPt

    • Insert a flathead screwdriver between the chassis and the plastic clip securing the control panel cable.

    • Compress the clip and slide it out of the chassis to remove it.

    • Move the cables out of the way of the detergent dispenser hoses before you continue.

  10. D3i2u4IZQbXcD5As

    • To prevent confusion, label each hose and its corresponding dispenser connection.

    • You can use masking tape or mark the components themselves.

  11. gdWTROQ2DwwlCX2O
    gdWTROQ2DwwlCX2O
    eJR22ILdEysTGysd

    • Use slip joint pliers to pinch the detergent dispenser hose clamp and pull it away from the assembly.

  12. fdo2dLaiBW1RnCCN
    fdo2dLaiBW1RnCCN
    KxL2GxhDJCqaD5Im

    • Use slip joint pliers to gently rotate the detergent dispenser hose back and forth around its connection and loosen it.

  13. NFketUDohaaBh5oH
    NFketUDohaaBh5oH
    crdEIEp16NRMBcSn

    • Pull the detergent dispenser hose straight off its connection on the assembly.

    • Repeat the loosening and removal procedure for each hose.

  14. nxbLNYd1WGw2eCky
    nxbLNYd1WGw2eCky
    romueM3OaV2hTNfQ
    kG1VCKeENvPPPXsg

    • Use a Phillips driver to loosen the screw securing the bellows to the detergent dispenser.

    • Pull the bellows straight off its connection on the dispenser to disconnect it.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Bill Gilbert

Member since: 30/06/22

37443 Reputation

0 comments