Infant Optics DXR-8 Monitor Screen Replacement

Written By: Daniel Edward Camp
  • Comments: 7
Infant Optics DXR-8 Monitor Screen Replacement

Difficulty

Moderate

Steps

7

Time Required

20 - 35 minutes

Introduction

If the monitor screen isn’t properly displaying images or camera feed from the Infant Optics DXR-8 cameras, it may be time to replace the screen. Follow these instructions to replace the screen in the monitor of the Infant Optics DXR-8.

  1. GOcvjwfgMcdXpsse
    GOcvjwfgMcdXpsse
    ZsNhD23SUDoHGrU5
    jT1ghDUBpspqWsjW

    • Using the plastic opening tool, remove screen protector from front of monitor.

    There's a layer of adhesive between the screen protector and the white plastic behind it.

    Jared Astillero -

    The cover is glued on. So you’ll nee d quite a bit of force to bend it up. But then it’ll come lose glue point by glue point. At first I was afraid that I’ll break it.

    Marco Smolla -

  2. N5QZknKvCQOlQXcL
    N5QZknKvCQOlQXcL
    GhBMVduKGErGhmVM
    lI14wgJlKmQ6WYFx

    • Remove the six 4mm screws using a Phillips #00 screwdriver.

    • Remove the screen, exposing the circuit board.

    • Turn device over to expose rear circuit board.

  3. ShALDj4QaI4Vpy54
    ShALDj4QaI4Vpy54
    PhVBd2P6MqTojxIG
    iC566Cdq64cWCCCA

    • Disconnect speaker from monitor for ease of access by unplugging wire.

    Thank you so much for this - and thank you to the commenter who walked through the additional screen replacement steps! I’ve never done anything like this and I managed to replace the screen myself.

    Lauren Skinner -

  4. 3mxT3UFPZNBbQ5KY
    3mxT3UFPZNBbQ5KY
    HCwHm4iZCexMVHPh
    YSpn5HJdAW6gpL1L

    • Using a plastic opening tool, disconnect the ribbon cable connector.

    • Gently separate the ribbon cable from the motherboard.

  5. BaOehy5OxjtP2DTx
    BaOehy5OxjtP2DTx
    YcJdklhlUbS1UJAh

    • Using a Phillips #000 screwdriver, remove the four 4mm screws around the edge of the motherboard.

    • Flip the motherboard away from the front case to reveal the screen on the other side.

  6. EsQFVVhnASSPfEHr

    • Using a plastic opening tool, carefully pry the top retaining frame off of the screen. Start in one corner and work around the bottom of the frame.

  7. SMBS6OtdBHWXNJVf
    SMBS6OtdBHWXNJVf
    14BwXXZbBj4J4cee
    S6EReWFb4RK1ScWa

    • Using a plastic opening pick, carefully pry a corner of the screen away from the motherboard.

    • Lift the screen off of the motherboard.

    What do you do when you reassemble everything and the screen only shows white and nothing else? You can still hear the sound, but no image.

    Louise -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Daniel Edward Camp

Member since: 18/02/21

137 Reputation

3 comments

Hey Daniel!

Thanks for sharing ??

Where did you get the replacement part?

Ro Brandi -

On Amazon is the quickest option.

Hilitand LQ035NC111 LCD Display, 3.5inch TFT RGB LCD Display Module 320 x 240 Display Panel LQ035NC111 54pin LCD

Stebe -

Just completed the screen change, it works great! Thanks so much for this step by step guide.

The screen I ordered came with the metal brackets. Since the base was glued to the motherboard, it took a few extra steps of de-casing the one I got and re-casing onto the board. But worked fine.

I ordered: https://www.amazon.com/dp/B07NYN5PK2?psc...

James Quinlan -