Lenovo IdeaPad Flex 5 14ARE05 Display Replacement

Written By: Jaynilson
  • Comments: 0
Lenovo IdeaPad Flex 5 14ARE05 Display Replacement

Difficulty

Easy

Steps

9

Time Required

10 - 15 minutes

Introduction

Is the display to your Lenovo IdeaPad Flex 5 14ARE05 giving you problems? In this guide, you will find a step-by-step guide on how to replace it. The display allows you to interact with your laptop. When it malfunctions you may have problems with a flashing screen, or an unstable picture preventing you from using your laptop effectively. Before starting this guide make sure to power down the laptop and disconnect it from any power sources.

  1. R4lYK5PXAkNOdcjX
    R4lYK5PXAkNOdcjX
    xqxAmCobnKokTOAv

    • Remove the five 8 mm screws using a T5 Torx Screwdriver.

    • Remove the four 5 mm screws using a T5 Torx Screwdriver.

  2. HwtkrMZkE2OqwIEF
    HwtkrMZkE2OqwIEF
    WUyTexyonFSVlPmM
    bAnVludL24GYkq51

    • Use a small suction cup to pull open the back case at the two hinge cutouts.

    • Gently, use the plastic opening tool around the edges of the laptop to pry up the rest of the back panel.

  3. FL5yx2KEMmAOlHcP

    • Once all the clips have been disengaged, lift off the back cover.

  4. kr61OKTNgZtRtNeD
    kr61OKTNgZtRtNeD
    fCjvTN1qMmEKRDCK

    • Remove the four 5 mm Phillips #00 screws that secure the battery in place.

  5. 5Fqf42Z4Go6MEKmJ
    5Fqf42Z4Go6MEKmJ
    uotgmfNhY3NDtIYV

    • Rotate the device 90 degrees.

    • Gently lift up on the battery and use a spudger to disconnect the battery connector.

  6. oWRf6KYwMZPEH6Vw

    • Remove the four 2 mm screws using a JIS #1 screwdriver.

    • Remove the three 5 mm screws using a JIS #1 screwdriver.

  7. p3HGs6b6Yvt6rqNo
    p3HGs6b6Yvt6rqNo
    2o3CJbqvSVER1swg
    VEOBIZ6QFMfaqkV4

    • Unplug the wire at the bottom right of the fan.

    • Carefully lift the fan from its place.

  8. 51rJrmLJdtCrIKKt
    51rJrmLJdtCrIKKt
    UD6ciSr6VoDXge5H

    • Disconnect the two connectors connected to the display.

    • Be careful not to break any of the wires or connectors.

  9. TudoxwQZChNY1hPj
    TudoxwQZChNY1hPj
    vgnq46LXQucPwEAg

    • Remove the three 2 mm screws from the left hinge using a Phillips #2 screwdriver.

    • Remove the two 2 mm screws from the right hinge using a Phillips #2 screwdriver.

    • Bend the metal brackets, lift the hinges off the frame, and remove the display.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Jaynilson

Member since: 18/10/24

97 Reputation

0 comments