Motorola Atrix 4G Bottom Speaker Replacement

Written By: Jake
  • Comments: 10
Motorola Atrix 4G Bottom Speaker Replacement

Difficulty

Moderate

Steps

14

Time Required

15 - 20 minutes

Introduction

To remove the speaker you will need to remove the battery, open the phone and remove the motherboard. Be ready to use a plastic opening tool, T5 Torx Screwdriver and a spudger.

  1. a1r2R5ydjKekW25K

    • Pry the back cover off the back of the phone.

    Use the word "prying" rather than sliding. We were confused during this step.

    Ben Sweeney -

  2. EJWeUmNXGOh6A2iW
    EJWeUmNXGOh6A2iW
    ZQZQYOUrbAKNNUKw

    • Insert a spudger into the small notch at the base of the battery.

    • Lift the battery out of the phone.

  3. nsKeA5cnSFthTWrd
    nsKeA5cnSFthTWrd
    ZjqbO5CpSooDsMhQ

    • Remove the four 5.0 mm T5 Torx screws using a T5 Torx Screwdriver.

    • Remove the three 5.5 mm T5 Torx screws using a T5 Torx Screwdriver.

    • Use gentle force while unscrewing to avoid stripping the screws.

    Not a phillips head screwdriver. Indicate the appropriate tool.

    Ben Sweeney -

    Hex head screwdriver.

    Ben Sweeney -

  4. 3vLtDRKaXUGMB1sf

  5. qibBxHwAVSSEHb2v
    qibBxHwAVSSEHb2v
    RnEuAgIOTsE6c2sq

    • Gently lift the tabs located at the top of the phone using an opening tool.

    • Gently lift the tab located at the bottom of the phone with the same tool.

    • Use an opening tool, not your fingers, because the plastic tabs are easily broken.

    Red boxes around the tabs so all can be seen clearly. Change the bullet point to red to accommodate said boxes.

    rubixtriangle -

  6. 6FPyx2mFZ3eawssV
    6FPyx2mFZ3eawssV
    TYnciSATVIHO4CcU

    • Insert an opening tool between the front and back of the case.

    • Slide the tool down the side of the phone.

    • Repeat the same process for the other side.

    • There should be a noticeable gap between the front and back cases. If not, repeat this step.

  7. SaoPrZJ1AmaYfD2u

    • Carefully lift the back case off the phone.

    • Do not completely separate the back case from the phone. The antenna is connected to both cases.

  8. bl2IRTwEZZXXIRM4

    • Slide an opening tool beneath the antenna and lift straight up from the motherboard.

    • Lift straight upwards, not at an angle, to avoid damaging the socket underneath.

    Specify--lift beneath it near the gold metal piece located on the phone (not the back case)

    Ben Sweeney -

  9. ZEQt1FgYuEPLthes

    • Ease the antenna from out of its guide along the side of the phone

    • Remove the back case and the antenna from the phone.

    • The antenna is soldered to the back case. When reassembling, do not pull it with too much force.

    Add picture for "easing out of the guide." Also, specify that you must unclip the guide from the phone.

    Ben Sweeney -

  10. NCQQCY3MWZcc3BoH
    NCQQCY3MWZcc3BoH
    jIQIyQat6YCKPP5F

    • Insert a spudger between the black plastic and the motherboard.

    • Lift upwards with the spudger to dislodge the board.

    • The motherboard should lift up easily. If the white rubber piece shifts, move it back to its original place.

    Specify "right side."

    Ben Sweeney -

    Not clear instructions. Clear/white rubber piece came off during removal--make a note of that possibility.

    Ben Sweeney -

  11. xJFk3g3dWoa1hOQ3

    • Disconnect the press connectors using a spudger.

    • If you are unfamiliar with using connectors, consult this guide.

    Add color bullets.

    Ben Sweeney -

  12. 26PBfVglSOdyWOON

    • Lift the white latch on the ZIF connector using a spudger.

    • Gently pull the black ribbon down and away from the latch.

  13. mHcHpQr2lhEEZmdm

    • There should be five distinct parts of the phone: the back cover, the back case, the front case, the battery, and the motherboard.

  14. tkWJjxMWy4aUDCK4
    tkWJjxMWy4aUDCK4
    kOFg1ANpIOCgZHDV

    • The speaker can be found on the bottom of the inside of the back case and is held in by glue.

    • Use a spudger or case opener tool to pry out the speaker by sliding it in the crack between the two pieces of black plastic.

    Where does the bottom speaker makes contact with the logic board?

    Paragon -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Jake

Member since: 19/04/12

515 Reputation

0 comments