Petcube Play 2 LED Replacement

Written By: Christopher Pereira
  • Comments: 0
Petcube Play 2 LED Replacement

Difficulty

Difficult

Steps

10

Time Required

45 minutes - 1 hour

Introduction

If the microphone of your Petcube Play 2 (identified by model number PP2OUS) is malfunctioning, use this guide to replace it.

The Petcube Play 2 comes with an LED that turns different colors that relay what state the Petcube is in. These can include when the LED turning green when setting up, turning blue when it is streaming, and error-related colors like orange when there is no access point. A defective LED will not turn on.

Before using this guide, ensure that there are no other issues with the LED. The Troubleshooting Page covers issues that could be preventing the LED from turning on and how to address them.

Ensure the Petcube Play 2 is turned off before beginning the replacement process. This guide requires soldering. For more information on soldering, take a look at this guide on How to Solder and Desolder Connections.

  1. sMTQVfJPAu3Wfpyj
    sMTQVfJPAu3Wfpyj
    YZm32gY1JjIKOLf6
    bwQVW56e3kBMmAw4

    • Flip over the Petcube so the rubber bottom faces you.

    • Pull up the rubber layer with an iFixit opening pick to expose the screws underneath.

  2. ordYilaDRog5ySti
    ordYilaDRog5ySti
    CeoJKE5tZ5XEKOD4

    • Remove the four 3.5mm screws from under the rubber cover with a Phillips #1 screwdriver.

    • The glue may cause a bit of resistance but the screws should come up without much effort.

  3. 3T1Of5ETAMuDG5Bt
    3T1Of5ETAMuDG5Bt
    UNhQffaoWFbOVdFq

    • Carefully pry off the glass front panel with an opening pick or spudger.

    • Do not force the front panel off as it may crack and break.

  4. KhnQSTOOHbAXc1Kn
    KhnQSTOOHbAXc1Kn
    cH1C2tsymTaHAQhB
    PvTfFxEwOdm3OeSm

    • Slide off the two covers, starting with the top plastic cover.

    • Slide out the internal assembly from the aluminum.

  5. t43BjCtj21qu1LGG
    t43BjCtj21qu1LGG
    ZmncrHe4FjOVpIyr
    DDTPWhoPwwO1Jjyn

    • Once the internal assembly is removed, a brass cylinder in a corner of the front face of the cube should be visible. Connected to the cylinder is a screw.

    • Remove the screw with a Phillips #1 screwdriver.

  6. EFAuaOmoTElvYJ4S
    EFAuaOmoTElvYJ4S
    TOkgOFc3Ftm55CYQ
    Of5aDTItTeTWlRdX

    • Flip the cube onto its side to locate the pull tab(s).

    • Flip the cube onto its side to locate the pull tab(s). Using an opening tool, lift each of the five tabs to separate the two halves of the Petcube 2.

  7. SdjIpAqYoIoVk3Wo
    SdjIpAqYoIoVk3Wo
    w4Kb2hGZqJb2g6Xo
    fPyAeEwOZyHZtH3N

    • Gently disconnect the cable connectors to separate the two halves of the device.

    • Make sure to avoid pulling on the wires to prevent breaking them or the connectors.

  8. HZFsBEULtmgBFuUF
    HZFsBEULtmgBFuUF
    55ummO6BqnqFkZ2D
    3TQGAZLmkJtsvLbp

    • Use the Phillips #1 screwdriver to remove the two 1mm screws.

    • Carefully release each of the tabs located on the sides of the cube and take out the motherboard.

    • Be gentle with the tabs as they will break under too much pressure.

  9. KOyOWFqDSIL6IPKA
    KOyOWFqDSIL6IPKA
    QOU5dFylaVVIaIYC
    ofXfE6T6ewappIn1

    • Using a Phillips #1 screwdriver, remove the screws to disconnect the front plates from each other.

  10. BUNuIMFTQRJL5tGn
    BUNuIMFTQRJL5tGn
    51WyTQgVGfLcTA6i
    AY1HDIvQANErnA1a

    • Remove the front plastic casing from the circuit board.

    • Identify the LED and the foam protector.

    • Remove the foam protector by gently pulling upwards with thin tweezers.

    • Use a soldering iron to desolder the LED from the board. Solder the new LED in the same place and orientation.

    • Never touch a hot soldering iron.

    • When soldering, be careful not to damage any other components be resting the iron on them. Remove the solder on the LED only, then solder the new one on.

Conclusion

To reassemble your device, follow these instructions in reverse order. Take your e-waste to an R2 or e-Stewards certified recycler.

Author

Christopher Pereira

Member since: 18/03/24

181 Reputation

0 comments