Introduction

Use this guide to remove or replace the back panel on an Xbox Series X (2TB Galaxy Black edition).

Before you begin, completely power down and unplug all cables from your console. Remember to follow general electrostatic discharge (ESD) safety procedures while repairing your console.

  1. RVl55HBQvdetmSvB
    RVl55HBQvdetmSvB
    bninbkWq1A3JUpAc
    KABeVTVxpkLJFcXx
    • Before you begin, completely power down and unplug all cables from your console.

    • Use a pair of tweezers to remove the sticker hiding the first screw on the back panel, near the base.

  2. K4xhH6KyAKefxNPf
    K4xhH6KyAKefxNPf
    LKWeh2voLVCkB2S2
    BhSNKZqZoRyUagr3
    • For cleaner removal, use an iOpener or hair dryer to heat the sticker.

    • Use a pair of blunt tweezers to peel back the large sticker on the back panel to reveal the second screw.

    • You only need to peel this sticker to where you can access the hidden screw. You don't need to pull it completely off.

    • Technically, these are tamper-evident stickers, but don't worry—Microsoft can't legally void your warranty, as long as you don't damage anything. Have fun!

  3. JHlVtqMo2mYuLYqU
    JHlVtqMo2mYuLYqU
    DDJZMCrp4jdKibXp
    • Use a T8 Torx driver to remove the two 7.4 mm‑long screws securing the back panel.

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your console.

  4. H2vDPcDIVvSraKLb
    H2vDPcDIVvSraKLb
    Ci1N4TNyoUHgDbIL
    YgokPmUJA4dPS42A
    • Insert the flat end of a spudger into the gap between the back panel and the shell, near the left side of the base.

    • Pry up the back panel to release it from the locking clips.

  5. 1MkWNRXA5UoF3xIg
    1MkWNRXA5UoF3xIg
    EhweH3oqCytMOFER
    • Insert the flat end of a spudger into the gap between the back panel and the shell, near the right side of the base.

    • Pry up the back panel to release it from the locking clips.

  6. VZLHaMniba2rLHWM
    VZLHaMniba2rLHWM
    XvF6R5ceStYjXxWJ
    TKgSJCCImCotgsQD
    • Grip the back panel at the opening you just created and pull it up and away from the shell to unclip the long edges.

    • During reassembly, press along the edges of the back panel to snap it into place.

  7. CGCSwKMAKnv3bArr
    CGCSwKMAKnv3bArr
    RFQ5eLxqPSIVrGAO
    SYnBeLFltCZPMuoM
    • The back panel slots into a gap at the top of the shell.

    • Tilt the back panel up and pull it away from the top edge of the shell to release it from the gap.

    • Remove the back panel.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Xbox Series X Answers community for help.

Spencer Day

Member since: 14/09/22

95592 Reputation

0 comments