eufy Clean RoboVac G32 Pro Motherboard Replacement

Written By: Manuel Chias
  • Comments: 1
eufy Clean RoboVac G32 Pro Motherboard Replacement

Difficulty

Moderate

Steps

21

Time Required

5 - 10 minutes

Introduction

A replacement guide for the motherboard for the Eufy Clean Robovac G32 Pro.

The motherboard hosts all the electronics systems in the same space to allow them to communicate with one another. Without this, it would not be possible for the device to operate.

If the individual parts are functional, but there's a problem with the device, it could originate with a faulty connection between them and the motherboard.

  1. kkQCTvkSP3QLY2Vh

    • Make sure your device is turned off.

    • Flip the device upside down on a flat surface.

  2. JHYFyrMeJWJE5nfB

    • Remove two 10 mm screws using a Phillips #1 screwdriver.

  3. qKARaaBdoFGDlySF

    • Lift the cover of the battery.

  4. Mj142opP3EbqmFVM

    • Lift up the battery using the white straps on the side.

  5. xhkwJmnYgpGFKpTb
    xhkwJmnYgpGFKpTb
    KNgQOQZBLiDnWEdq

    • While holding the battery, pinch the clips on the side of the white connector.

    • Using a spudger, push the part of the connector inside of the Robovac away from the white connector on the battery.

    • Pinch the clips hard; they may be a little stiff.

    • Remove the battery from the device.

  6. sUldhxepALWuDPUH

    • Make sure your device is turned off.

    • Flip the device upside down on a flat surface.

  7. Yvnt1HVNdt1UK4dJ

    • Press the clips at the bottom of the device that are indicated by the downward facing arrows.

    • Take off the rolling brush cover.

  8. Sr2TWaVZ2nBqmtDM

    • Pull the rolling brush up on the right side. Remove the rolling brush.

  9. GXZYEhuhhgtfGpoS

    • Make sure your device is turned off.

    • Flip the device upside down on a flat surface.

  10. 3NQMyQ6uWZ6xOXYY

    • Remove four 10 mm screws using a Phillips #1 screwdriver.

  11. k5g6VCAXbBL6s5US

    • Lift up the wheel.

    • Lift firmly but gently as the wheel's connection to the motherboard is delicate.

  12. O6sj5EikrnPrDIuN

    • Disconnect the spring from the wheel.

  13. 1C53iJjvrlgQ21dV

    • Remove the motherboard wiring from the wheel.

    • Pinch the white cable connecting the wheel to the wiring and pull.

    • Remove the wheel from the device.

  14. SPKgsfGme5VxVAsH
    SPKgsfGme5VxVAsH
    MZUavGHqCj6nANNy
    nuXExWwHDPaVBRyq

    • Orient the device so the underside is facing up.

    • Remove the eight 9.3 mm screws securing the bumper brackets using a Phillips #1 screwdriver.

    • Remove the bumper brackets.

  15. KjOS2gKPoeQXwE46
    KjOS2gKPoeQXwE46
    xbXhTKQJgD1vvZIL

    • Lift the bumper off of the device gently.

    • Use your fingers to disconnect the 8 pin connector.

  16. jVxN4NrUljdZbVEt
    jVxN4NrUljdZbVEt
    ObeCrGaJfBMShlRt

    • Remove the two 10 mm screws using a Philips #1 screwdriver.

  17. AVZF1iM3IiKBqIPj

    • Lift the bump sensor off using your fingers.

  18. RsPIfFHCM61oZSrr
    RsPIfFHCM61oZSrr
    fi2FrnjRuQy1WlfM

    • Remove the eight 14 mm screws with a Phillips #1 screwdriver.

  19. JKqbEygpJbw4WgnX

    • Use your hands to separate the two halves by lifting the cover from the end that has the brush, as the cover is still connected.

    Also, the two screws under the roller need to be removed

    Steve M -

  20. FkwwngCXmt22avJC
    FkwwngCXmt22avJC
    nLShMXFt4FDvNwvR
    GMxxutk5jq3mLHFa

    • Remove the three 9.7 mm screws securing the motherboard with a Phillips #0 screwdriver.

  21. tVOFisslvW3PuOmf
    tVOFisslvW3PuOmf
    rcKtUXraFCbvi2VX

    • Disconnect all connectors attached to motherboard.

    • Using your fingers, pull the connectors away from their ports by the plastic bit of the wire.

    • Pulling from the wires themselves could lead to the wire(s) loosening from the connector.

    • Remove the motherboard.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Manuel Chias

Member since: 19/09/24

109 Reputation

0 comments